[ad_1]
To retrofit underfloor heating – in other words, to install underfloor heating (UFH) in an existing home as part of a renovation – doesn’t offer quite the same clean slate for installation as a self-build would. But that doesn’t mean underfloor heating is out of the question.
There’s a selection of specially designed systems tailored towards renovation projects. It’s simply a case of tracking down the product that best suits your house’s characteristics. Thanks to a thin height build up and easy installation, electric systems were once the go-to solution for retrofit scenarios. However, thanks to the development of many slim, low-profile systems, installing warm water UFH in an existing house is more achievable than ever.
‘It’s particularly reassuring to know that you no longer need to dig up your floors to bury a system beneath six inches of screed and cement,’ says Tom Edmunds, general manager at Wunda Group.
How to retrofit underfloor heating – the step-by-step process
1. Decide on the most appropriate system to retrofit
When it comes to choosing the correct setup, there are several key factors to bear in mind. The first is the thermal efficiency of your home. If the house is poorly insulated with single glazed windows, the thermal fabric will likely require upgrading to ensure UFH can run efficiently. The type of subfloor you have also plays a big part in the decision, too. As will the amount of upheaval required for installation.
Image credit: Future plc/Chris Snook
Underfloor heating to an existing space can be divided into two categories. Systems that warm the floor surface via electrically heated cables, or those that comprise a network of pipes filled with warm water. The one you choose will depend on how many rooms you’re fitting UFH in. Plus how much you want to spend on installation and how much you’re willing to spend on running costs long term.
Electric
Electric underfloor heating comes either in loose cable form or with the wires embedded into a sticky mat. It’s easy to lay directly atop the subfloor and have little impact on floor heights – a key factor for many renovations where you can’t change ceiling heights and door levels.
‘Warmup’s StickyMat System features an extremely thin heating wire,’ says Sarah Wazir, a marketing executive at Warmup. ‘It can be installed directly in a layer of tile adhesive when you’re fitting the system alongside a tiled surface.’
Warm water screeded
In this system, warm water pipes are embedded into a layer of sand and cement screed that helps spread the heat across the floor surface. In the past, the height build-up from this layer would have required the removal of skirting boards and for the bottoms of doors to be trimmed down to fit. However, modern low-profile systems for renovations are designed with a thin, self-levelling liquid compound in place of the screed. This can reduce the typical height of the system from around 75mm to as little as 15mm, depending on the product you go for.
Warm water non-screeded
Hydronic systems with no screed can also be known as ‘dry’ – don’t confuse them with electric UFH, which is sometimes described using the same terminology. Here, pre-routed tubes are laid into a panel, which often features a layer of foil on top to help spread the heat effectively. Overlay systems like this can be laid directly onto the existing floor and are ideal for homes that don’t have the vertical space for a screed or self-levelling compound.
2. Budget correctly
Before you start your project, bear in the underfloor heating costs. If you’re retrofitting underfloor heating, bear in mind that any renovation project comes with more unknowns than if you were working with a brand-new building. That’s why it’s so important to build a contingency fund into your overall budget.
It’s generally acknowledged that laying UFH in an existing home will be more expensive than in a fresh new self-build, too – especially if you’re making thermal upgrades to your house as part of the process.
Electric underfloor heating costs less to install than warm-water systems as it’s so easy to fit. However, it will result in higher running costs later.
If you’re only fitting it in the family bathroom and an ensuite, that may not be a problem. However, if you’re retrofitting UFH across the entire ground floor, a hydronic system will probably be more cost-effective in the long-term.
3. Inspect your subfloor
If you have suspended timber floors (eg a period property), there are two options. One is to take up the floorboards completely and lay the underfloor heating pipes so they’re suspended between the joists, with a layer of insulation underneath. A sand and cement mix would then be poured around the pipes on top of the joists. If adding the screed layer is going to cause any issues, a low-profile overlay system with insulated backing boards might be the better option, as it can be laid on top of existing floorboards.
For homes with concrete slab floors, the process will generally be less labour intensive as you can simply lay UFH over the top of the floor slab. A screeded solution will offer the best heat output, however, if you don’t have the vertical height to accommodate that, a modern slimline product might be the best match.
Electric systems can typically be laid over concrete slab and suspended timber floors without any difficulties.
4. Lay a suitable flooring on top
Many materials are compatible with underfloor heating, but if you want your floor to conduct the heat effectively into the room above, dense tile surfaces have the edge. Solutions such as porcelain and ceramic are smooth and level, so you’ll get an even spread of warmth across the whole tile. Stone works well, too.
Timber is a possibility, though it won’t match porcelain or ceramic tiles in terms of its heat conductivity. Engineered products made from several cross-laminated layers of plywood, finished with a top veneer, are typically chosen over solid boards. Any floor finish that uses solid wood will need to be designed properly to allow for expansion and contraction as the wood heats and cools with your heating.
If you’re after a soft feel underfoot, carpet works. However you’ll need to ensure the combined value of the carpet and the underlay doesn’t exceed the Tog value specified by your UFH supplier. Otherwise, the layer of carpet will be too insulating for heat to move up into the room above.
Image credit: Future PLC/Colin Poole
Are there any other key considerations?
As it’s a low-temperature heat distribution system, UFH works best in homes that don’t leak heat through the walls, floors and roof. ‘To prevent heat loss, it’s always a plus to add insulation or improve the quality of the windows and doors as much as possible,’ says Michael Schienke, director at Vorbild Architecture. ‘Some of this may require separate permissions, but it’s always a plus to upgrade old single glazed windows to double glazed.’
In retrofit scenarios, floor profile is another key factor. ‘One of the biggest issues we face is keeping the existing floor finish level if you have areas in the house with UFH and areas without it positioned side by side,’ says Michael Schienke. Getting this aspect of your project right will come down to careful planning at the design stage. And making sure you choose the right product in terms of height build-up.
The post How to retrofit underfloor heating – a complete guide appeared first on Ideal Home.
[ad_2]
www.idealhome.co.uk
